本帖最后由 星丹 于 2010-3-24 14:36 編輯
7 w4 M% m+ y* M* w2 h4 W
. Z% | M, u1 y& G Z# _1 c貼圖① 剝離和點蝕 Flaking and Pitting: v1 H& [* F. P2 g$ h8 n3 J* |
) M& {# ? v- V7 d現象,、原因和對策; z" p8 y8 O. |$ {. x
Phenomena , causes and countermeasures 失效示例" k, [' m- z1 P1 q# Y) U
Examples of failures
5 {) N) [6 X+ Q$ c6 }2 nPhenomena 剝離是指因材料的滾動疲勞在滾道面及滾動面表層部分出現的魚鱗狀損傷,。產生這種現象時，可認為軸承已達到壽命,。
, w* A- u' H8 ~, e c% q7 a* s1 _因材料的滾動疲勞引起的損傷還有點蝕,，是指在滾道面出現的深度為0.1mm左右的微孔
' X0 a3 }" J1 {7 R3 uFlaking is a phenomena in which the bearing surface turns scaly and peels off due to contact load repeatedly received on the raceway and rolling surface during roataion. Occurrence of flaking indicates that the end of a bearing’s service is near.
# Q1 ^1 i& M) O2 b- Q0 F4 }# GPitting is a phenomena in which small holes 0.1mm in depth are generated on the raceway surface by rolling fatigue. ! [0 n) [7 E- F- l. H
3 @1 @0 M# R1 {% U) ?# V5 P @2 Q/ D8 z7 U
Causes ● 軸承內部游隙過小
5 q. Q* ~/ g$ @ T8 YDuring operation,bearing internal clearance becomes narrower than specified. n- b/ ^2 J4 [
● 軸承安裝不良7 K9 r- r2 z3 Z) x6 E
Bearing is mounted at an inclination by mistake .' d/ |" }; H. k) E2 K" b7 `
● Flaw is created during mounting,brinelling ,nicks,rust etc.
( j6 Y1 B: z+ P1 o● 軸或外殼的精度差
& E2 J t4 r) }6 T, g( u4 OInaccurate shape of shaft or housing. 3 L* v; e, b U: T; y# t) z
Countermeasures ◆ 選擇合適的軸承內部游隙; U' r, T b1 x- A; R
◆ 正確定心0 b) J' q; F! T1 @. e, J
◆ 修正軸或外殼擋肩端面的垂直度
7 u3 ~! w* q- m◆ 改進安裝作業方法 |
發表于 2009-10-13 15:19:10
QQ好友和群
收藏
淘帖
問題專業,，描述清楚
伸手黨/灌水/看不懂
