求翻譯

jackline

外語不精,，求達人翻譯,，謝謝

0 |; D" S+ f6 F1：垂直度超差：圖紙要求Φ125±0.011外圓和端面的垂直度公差0.03mm,實測0.06mm
( b/ t" E5 m* g$ s& Q
6 I3 D. U2 T0 n' [9 l! w2：平行度超差：圖紙要求部件底部裝配基準面與裝導軌平面平行度0.02mm,，實測0.05mm
9 S; c; i4 V- h# l3：直線度超差：實測導軌止口直線度0.26mm（中凹）
' X! h& B$ Q3 C; y5 E+ d* S/ V4：尺寸超差：  圖紙要求 Φ150+0.04孔中心線與底面尺寸為145±0.03mm,實測144.94mm
4 U+ U7 R5 ]% B7 b3 T. |% Z0 J6 V5：裝配基準面有2處補焊,，凸0.03mm（長15mm寬5mm）附照片

神奇寶貝

1.Perpendicularity is out of tolerance: drawing's  requirement is Φ125±0.011, perpendicularity tolerance of the outer circle and end face is 0.03mm, fact measurement is 0.06mm.
2. Parallelism is out of tolerance: the required parallelism between the bottom assemble datum plane and guide installiaton plane is 0.02mm, fact measurement is 0.05mm.
, E2 f8 D3 r' n$ L" b3. Straightness is out of tolerance: fact measurement of the guide's front edge is 0.26mm(Middle is concave)
4 |* ~0 O8 X4 Q: g( m5 W( [4. Dimension is out of tolerance: drawing's  requirement is Φ150+0.04, distance between the hole center and the bottom is required 145±0.03mm, fact measurement is 144.94mm.
5. There are two repair-welding on the assemble datum plane, protruding 0.03mm(15mm long and 5mm wide), see attached photo.

jackline

回復 jackline 的帖子

6 |* b8 r0 Z" p& @  f5 N" |受益匪淺,，灰常感謝
/ ]0 ^4 w( o" g+ T1 v4 b還想問個問題：尺寸超差,，可以用 Dimension is undersize/oversize,或dimension is not correct表示嗎,？

9 t/ o: N2 U, a' F
  v  W# R+ H/ `+ A  c2 v, }

神奇寶貝

jackline 發表于 2011-7-7 20:06
$ M, u* \6 h, Y0 H$ Y6 T6 W回復 jackline 的帖子
7 G* m, W$ t7 {# a. v* ~: D
受益匪淺，灰常感謝

沒用過,，也沒聽別人這樣用過

采彡銫莎氵莫

是和公司有關的,，又學習了

wugqtop

jackline 發表于 2011-7-7 20:06
0 N: U( r1 o7 I) C; X1 m0 X+ J回復 jackline 的帖子

" S" U4 |) Q4 t受益匪淺，灰常感謝

dimension out of tolerance
6 z; w) R( X1 @: l! L

kason127

用google翻譯好了�,�,！