我是一名autolisp初學者,，剛編了一段程序,，請教

月夢920

我是一名autolisp初學者,，剛編了一段程序是關于常用滲溝球軸承的參數化幾何建模的,，但是運行不出來,，怎么也找不出錯誤,。請各位前輩指點一下。,。,。
; @1 `. ^1 L$ w) @(defun c:zhoucheng()
, c7 n" Z/ J8 r& d. q+ R! s（setq p0(getpint "請輸入基準點："))
(setq d(getreal "內徑d=:"))
(setq D(getreal "外徑D=:"))
7 b/ K) ~6 f% G1 ]（setq B(getreal "軸承寬B=:")）
(setq r(getreal "滾子半徑r=:"))
(if(<r(*(-D d)0.5)) (princ"ok")
) i5 G2 @3 H) H  \& d5 j(setq p1(polar p0 (*0.5 pi)(*0.5 B)))
(setq p8(polar p0 (*-0.5 pi)(*0.5 B)))
(setq p2(polar p1 0(/(-D d)3)))
( d. T! Q2 ^: d: W7 b$ G, B5 q(setq p3(polar p2 0(/(-D d)3)))
" }* t2 C% O" l(setq p4(polar p1 0(-D d)))
(setq p7(polar p8 0(/(-D d)3)))
(setq p6(polar p7 0(/(-D d)3)))
(setq p5(polar p8 0(-D d)))
# G. }+ h3 X5 Q( j* Q$ M/ _(setq p12(polar p4 0 d))
' C* u: v! A+ A% x' l(setq p11(polar p1 0 D))
(setq p9(polar p5 0 d))
(setq p10(polar p8 0 D))
% C+ h' p5 F/ J) [, e(setq pt(polar p0 0(*0.5(-D d))))
, _( u6 A5 W. C4 \(setq p14(polar p0 pi(*0.5 B)))
% X& }. K' c8 E# B, O* D$ m(setq p15(polar p0 0(+D(*0.5 B))))
(command "layer" "s" "draw" "")
. b; \2 U! u/ r(command "line" p1 p11 p10 p8 p1 "")
(command "line" p2 p7 "")
(command "line" p3 p6 "")
" u/ r: D! \, Y8 ~(command "line" p4 p5 "")
2 G* n! n' n) z1 f' v! L) r(command "line" p9 p12 "")
6 d. s* Y0 t4 ~0 a" G(command "line" p12 p10 "")
4 W0 ]1 ^5 _  W(command "line" p9 p11 "")
* n7 m7 v: S7 N0 \: O(command "circle" pt r)
(command "trim" "all" "list(0 (/(-D d)3))")
: F* e7 U! I5 @1 H* H(command "trim" "all" "list(0 (*(/(-D d)3)2))")
/ y% v1 @) @  k2 t2 m4 N(command "bhatch" "p" "ansi31" 1 0,0 list(0 (/(-D d)5)) "")
(command "bhatch" "p" "ansi31" 1 0,0 list(0 (*(/(-D d)5)4)) "")
(command "layer" "s" "center" "")
(command "line" p14 p15 "")
& q$ R& q! g7 A  `9 l0 U0 y6 a
3 O8 ~  {, L* K' i8 S

復蘇之風

一步步的調試啊

LIAOYAO

{:soso_e120:}
7 I! f& o# ]. ]) E(setq p0 (getpint "請輸入基準點："))  
& Q$ s! ^/ O* m! P. d5 }(setq p0 (getpoint "請輸入基準點："))

（setq B(getreal "軸承寬B=:") ）
) r# y5 l1 g8 v0 @, ?(setq B(getreal "軸承寬B=:"))

6 u1 w. g) E- n7 V$ _; A(if(<r(*(-D d)0.5)) (princ"ok")
(if(< r (*(- D d)0.5)) (princ"ok") )
1 m. b4 ^" o1 I7 x
/ i/ u! A  j6 I; w7 E2 }(setq p1(polar p0 (*0.5 pi)(*0.5 B)))
(setq p1(polar p0 (* 0.5 pi)(* 0.5 B)))

不搞了,，就這幾行程序的語法疏漏或括弧或空格不對等等,，樓主自己逐行測試修改咯！
) W8 Q  Z5 d, F) R

兩岸猿聲啼不住

寫程序容易,，調試程序難,。。,。