美國的斜齒輪圖紙的英文,誰能幫忙翻譯下,不勝感激!

yang13564

1.
Quality: ANSI/AGMA 2000-a88-q11, full depth, full fillet.

2.
FOR LEAD, CROWN, AND PROFILE TOLERANCES SEE DWG 54773379

3.
. ?& n8 Q( W  ]9 n8 }% V1 X/ MCROWN DRIVEN GWAR ONLY

4.
NORMAL PRESSURE ANGLE 20”

5.
NORMAL DIAMETRAL PITCH 8

6.
+ P2 A/ j  d/ B8 x) ?2 ~NORMAL CIRAULAR PITCH 0.3927

7.
HELIX ANGLE:16.6011

8.
$ m2 b& F0 y' N* J) O! IBACKLASH TO BE 0.996” TO 0.008” ON 6.9784” CENTERS

9.
MATERIAL: AISI 8620

10.
CASE CARBURIZE TO 0.025” TO 0.040” EFFECTIVE FEPTH AFTER GRINDING AND HARDEN TO 57-61 RC, CORE HARDNESS
* T" t# q& ~4 @2 p: h# i) nTO BE 25-40 RC.

11.
6 a$ H# H5 q# D" ARETAINED A USTENITE – 5% MAXIMUM BY VISUAL INSPECTION.

12.
EACH GEAR DEAR SET TO BE BOXED SEPARATELY AS A SET AND EACH GEAR MARKED WITH THE SET PART NUMBER ON THE OUTSIDE. EACH GEAR TO HAVE P/N AND SUPPLIER INENTIFICATION STAMPED. EACH GEAR TO HAVE P/N AND SUPPLIER IDENTIFICATION SATAMPED OR ELECTRIC ACID ETCHED AS SHOWN, APPROX. TEXT HGT..25’.

13.
" @9 I; Q9 [5 k% b; u! G: p. j' \REMOVE ALL CHIPS FROM TAPPED HOLES.

NUMBER OF TEETH

HAND OF HELIX

LEAD OF HELIX

PIRTCH DIAMETER

BASE CIRCLE DIAMETER

ADDENDUM

WHOLE DEPTH

TRANSVERSE CIRCULAR

TOOTH THICKNESS WO/BL

NORMAL CIRCULAR

TOOTH THICKNESS WO/BL

yang13564

沒有人翻譯,找到了資料,不知道對不對!望高手出來指正!
        齒輪制造標準和精度等級：ANSI/AGMA 2000-A88,，精度12級，全深,，全倒角,。
        齒向、齒形修緣和漸開線輪廓公差按54773379圖紙規(guī)定,。
* D7 C. X% I: o  k        僅驅動齒輪鼓形修整,。
% k2 r! g  r  @9 P7 n        齒形壓力角20º
        節(jié)徑DP=10
        齒距：0.3142
        螺旋角：15.9355º
        在齒輪嚙合中心距5.5118”上，側隙要求在0.006” ~0.010”之間,。
) ^  q0 c' @+ }2 g        齒輪材料：AISI 8620
! E; f, ], h% K, u* K$ G        滲碳層0.025”~0.040”有效深度,，表面硬度為57~61Rc，芯部硬度25~40Rc,。
3 v1 p: h# T; r2 L( h, u: Q9 e        殘余奧氏體最大5%目測檢查,。
0 o' ^  O3 x- ]/ m0 N* {        每個周轉盒內只能裝一個齒輪組，周轉盒外標記齒輪組圖號,，齒輪表面須按圖示部位用電蝕法標記零件號和供貨商代碼,，字高約0.25。
        攻絲后,，去除螺紋孔內的鐵屑,。

qvzhiwei

樓上玩意的好專業(yè)，佩服�,。,。�

another

二樓挺專業(yè)的···感覺還不錯,，很值得學習,。