應社友要求,，共享SW鈑金零件輸出展開DWG的代碼

DaveChan · 發表于 2016-10-23 10:39:59

保留折彎線:

Option Explicit
2 ~, N: C! w1 X8 w
Dim swApp As SldWorks.SldWorks: p" {5 V& V9 h6 }
Dim swModel As SldWorks.ModelDoc21 I! w8 X) V& [7 M6 J
Dim swModelDocExt As SldWorks.ModelDocExtension
' L7 ^: p/ ?/ ^* U( e+ y2 u/ a- J
Dim FileName As String+ F0 [4 R# w" H& x' u4 E
Dim NewName As String
' s" d7 E+ G# t ]$ ]+ y: A
Dim boolstatus As Boolean
1 W. c% r |+ u7 |: ^
Dim longstatus As Long, longwarnings As Long2 H& }. |3 c8 j. j. v/ h4 j6 _: X6 ]5 F
Sub main()# _5 @) N# [0 u- Q! ~* D
Set swApp = Application.SldWorks* O6 q! {; _. E4 O0 u
Set swModel = swApp.ActiveDoc @6 _: j! |7 f- l/ a9 Z
Set swModelDocExt = swModel.Extension4 l0 }1 k, P5 p2 m. T: Y
FileName = swModel.GetPathName(); q7 G" P+ m }9 V
NewName = Left(FileName, Len(FileName) - 7) & ".dwg"
9 o. W% T1 J$ e* j) q
boolstatus = swModel.ExportFlatPatternView(NewName, swExportFlatPatternOption_None)
) Z' Q u4 s7 b. P$ S
swModelDocExt.SaveAs NewName, 0, 0, Nothing, longstatus, longwarnings+ N- |# _: u5 v& R' V7 ?/ o
End Sub
% M3 u* Z; @7 n6 g: q0 I

復制代碼

移除折彎線:

Option Explicit
3 s+ E) ?) j. q: V, U
Dim swApp As SldWorks.SldWorks% g! g: s/ K6 t9 F2 Q5 m" }
Dim swModel As SldWorks.ModelDoc2
& g9 {* a) V% Y/ j- n
Dim swModelDocExt As SldWorks.ModelDocExtension
g- q# ~3 u1 ~! e; K
Dim FileName As String, m4 q# S: H }" s/ d- \
Dim NewName As String: Y- X- n9 F6 N3 i
Dim boolstatus As Boolean. z& H: b o9 T6 ]' j
Dim longstatus As Long, longwarnings As Long
. |9 l" i' b2 s% V
Sub main()) b- m2 G8 }& G* {
Set swApp = Application.SldWorks
2 T+ a( G- s7 b; \7 o* K% x, |$ W
Set swModel = swApp.ActiveDoc8 r( f) }) w9 ?# }& ]
Set swModelDocExt = swModel.Extension
, i6 W8 T' L* A
FileName = swModel.GetPathName()' G+ j" o- w7 I% f# W
NewName = Left(FileName, Len(FileName) - 7) & ".dwg". |. ?# P" x( |
boolstatus = swModel.ExportFlatPatternView(NewName, swExportFlatPatternOption_RemoveBends)
2 ]& ^0 {! e& \+ p* `
swModelDocExt.SaveAs NewName, 0, 0, Nothing, longstatus, longwarnings
* Y$ m' |: a7 D/ R- i/ C( `6 M
End Sub+ X5 {/ i) q7 S+ A- U

復制代碼

響在江湖 · 發表于 2016-10-23 10:47:29

必須頂上去,！超實用�,。�

小飛熊l · 發表于 2016-10-23 15:39:50

沒覺得sw鈑金需要改動啊

newmorn · 發表于 2016-10-23 16:56:57

sw工程圖里面的平板形式不就是展開圖嗎？這都要寫代碼呀,？

機械路慢 · 發表于 2016-10-23 17:46:39

樓主,，這是？代碼要放到哪里,？

befuture · 發表于 2016-10-23 19:23:30

怎么用啊新手

hc2003 · 發表于 2016-10-23 19:49:24

樓主好人做到底,，說明一下怎么使用啊

DaveChan · 發表于 2016-10-24 08:23:43

本帖最后由 DaveChan 于 2016-10-24 08:54 編輯

newmorn 發表于 2016-10-23 16:56
7 i$ S: v/ Q6 K! {9 g+ ^sw工程圖里面的平板形式不就是展開圖嗎？這都要寫代碼呀,？

代碼替代了繁瑣的點擊另存為過程,，利用代碼做成宏按鈕，一鍵保存平板形式為dwg/dxf下面動畫為另存為輸出過程和宏代碼輸出過程

DaveChan · 發表于 2016-10-24 08:58:37

hc2003 發表于 2016-10-23 19:49
3 T; f# `$ F2 z樓主好人做到底，說明一下怎么使用啊

1.新建一個宏,，刪除里面所有代碼
2.復制我貼的代碼到這個宏里面
3.保存此宏
4.打開一個鈑金零件(可以展開的零件)
5.運行此宏
6.自動輸出展開圖(DWG)

		自動登錄	找回密碼
密碼			注冊會員