應社友要求，共享SW鈑金零件輸出展開DWG的代碼

DaveChan · 發表于 2016-10-23 10:39:59

保留折彎線:

Option Explicit+ l) E5 }4 [2 G" z4 D7 ~9 M+ p+ D
Dim swApp As SldWorks.SldWorks& P7 |. Q, U( m3 X/ b w
Dim swModel As SldWorks.ModelDoc2
( e0 N0 R1 N( j# S
Dim swModelDocExt As SldWorks.ModelDocExtension
- F4 |1 n z; I& n
Dim FileName As String# f; I- O7 n, G
Dim NewName As String
3 i1 V" {' [$ v0 S/ W
Dim boolstatus As Boolean
& W& a: @" S( m7 A& K& g" R2 M7 r* d
Dim longstatus As Long, longwarnings As Long
, q1 h$ Q4 ^' `# Y' o) R2 s
Sub main()
0 p4 p5 H+ [% }; P2 l, l2 \
Set swApp = Application.SldWorks
) z* J0 T- O/ ]9 O
Set swModel = swApp.ActiveDoc% |% i% f: ^% ^7 q$ H, ^6 |% i
Set swModelDocExt = swModel.Extension
7 n, U# g$ i4 H! m4 a$ J
FileName = swModel.GetPathName()( n/ t9 R$ \& k6 N$ m) M. w% c
NewName = Left(FileName, Len(FileName) - 7) & ".dwg"+ ?/ b3 \% { W# O8 a
boolstatus = swModel.ExportFlatPatternView(NewName, swExportFlatPatternOption_None)" w5 Y" T; H! E# `. J' H
swModelDocExt.SaveAs NewName, 0, 0, Nothing, longstatus, longwarnings1 F0 e( l1 |$ `9 V# ~0 I4 N
End Sub1 p+ \+ r; S' ^! e# @

復制代碼

移除折彎線:

Option Explicit; r# N0 g* V0 K* X K8 f; W
Dim swApp As SldWorks.SldWorks3 D/ a: J* p# X
Dim swModel As SldWorks.ModelDoc2
6 P& @$ B% L& L& P2 [5 z
Dim swModelDocExt As SldWorks.ModelDocExtension6 L1 Y' k, O) h3 b# H/ u
Dim FileName As String
" g7 R0 r- l* ^" T& \- N x
Dim NewName As String! Q9 o1 }0 l5 ~; M# R* R- |
Dim boolstatus As Boolean
# h3 I) D. z( `
Dim longstatus As Long, longwarnings As Long' n, a$ S! _0 ^: w8 Z+ G
Sub main()
. j# ]) f/ {+ y; q
Set swApp = Application.SldWorks( b5 G- q8 y3 _3 N. U) r' Z
Set swModel = swApp.ActiveDoc
( m3 R" [0 E: a3 z5 ^
Set swModelDocExt = swModel.Extension
+ X( M' T' R$ |
FileName = swModel.GetPathName()
# y( S0 ?/ s$ I5 j: D) u5 r: n
NewName = Left(FileName, Len(FileName) - 7) & ".dwg"
7 v$ ~# e) A6 o: Q$ }6 T
boolstatus = swModel.ExportFlatPatternView(NewName, swExportFlatPatternOption_RemoveBends)
; c: q6 F2 R1 C. z3 V$ c9 ^
swModelDocExt.SaveAs NewName, 0, 0, Nothing, longstatus, longwarnings' U5 x6 P& T2 g2 B, C3 x
End Sub
! B6 K% m6 Q V2 l4 b5 \) f

復制代碼

響在江湖 · 發表于 2016-10-23 10:47:29

必須頂上去,！超實用�,。�

小飛熊l · 發表于 2016-10-23 15:39:50

沒覺得sw鈑金需要改動啊

newmorn · 發表于 2016-10-23 16:56:57

sw工程圖里面的平板形式不就是展開圖嗎,？這都要寫代碼呀,？

機械路慢 · 發表于 2016-10-23 17:46:39

樓主，這是,？代碼要放到哪里,？

befuture · 發表于 2016-10-23 19:23:30

怎么用啊新手

hc2003 · 發表于 2016-10-23 19:49:24

樓主好人做到底，說明一下怎么使用啊

DaveChan · 發表于 2016-10-24 08:23:43

本帖最后由 DaveChan 于 2016-10-24 08:54 編輯

newmorn 發表于 2016-10-23 16:56( N+ l" G( `# Z2 f+ w2 U- n
sw工程圖里面的平板形式不就是展開圖嗎,？這都要寫代碼呀,？

代碼替代了繁瑣的點擊另存為過程，利用代碼做成宏按鈕,，一鍵保存平板形式為dwg/dxf下面動畫為另存為輸出過程和宏代碼輸出過程

DaveChan · 發表于 2016-10-24 08:58:37

hc2003 發表于 2016-10-23 19:49: L2 n0 Y5 n& g& A* ?5 N
樓主好人做到底,，說明一下怎么使用啊

1.新建一個宏,，刪除里面所有代碼
2.復制我貼的代碼到這個宏里面
3.保存此宏
4.打開一個鈑金零件(可以展開的零件)
5.運行此宏
6.自動輸出展開圖(DWG)

		自動登錄	找回密碼
密碼			注冊會員